|
Power
|
|
Input Supply Voltage
|
6 - 30 vDC, unregulated ( 12 vDC Nominal )
|
|
Current
|
167 mA
|
|
Power Consumption
|
2.0 watts
|
|
Power Connector
|
5.5mm x 9.5mm x 2.1mm barrel socket
|
|
Power Adapter
|
|
Universal AC/DC Adapter
|
100-240v AC, regulated DC adapter included
|
|
Indicators
|
|
Power / TST
|
This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.
|
|
Fiber link on / Receive activity (LKF)
|
This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received.
|
|
Copper link on / Receive activity (LKC)
|
This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received.
|
|
Switches - accessible through a side opening in the chassis
|
|
Auto-Negotiation (802.3u)
|
Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex.
Disabled - The media converter sets the 100Base-TX port to full duplex.
|
|
Pause
|
Pause should be enabled when all devices connected to the media converter support pause. Auto-Negotiation must be Enabled to use this feature.
Enabled (Default) - The Media converter will advertise Pause capability during Auto-Negotiation on the 100Base-TX interface.
Disabled - The Media converter will advertise that it does not have Pause capability during Auto-Negotiation on the 100Base-TX interface.
|
|
Link Pass Through
|
Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on.
Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface.
|
|
Far-End Fault (FEF)
|
Enabled (Default) - The media converter transmits the Far-End Fault Indication over the 100Base-FX fiber connection whenever a receive failure is detected on the 100Base-FX fiber connection. The media converter continuously monitors the100Base-X fiber connection and clears the Far-End Fault Indication condition when a valid signal is received.
Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection.
|
|
Remote Loopback
|
The media converter can perform a loopback on the 100Base-X fiber interface.
Disabled (Default - Up)
Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.
|
Auto-MDIX
(Internal Strap)
|
If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media convertor's transmitter and the partner devices transmitter are connected to the others receiver. The Media Convertor's 100Base-TX port is configured as MDI with this switch setting.
|
|
Cables
|
|
100Base-TX
|
RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable
|
|
Magnetic Isolation
|
1.5kv
|
|
Fiber Optic Cable
|
Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron
Single Mode: 9/125 micron (ITu-T 625)
|
|
Packet Transmission Characteristics
|
|
Bit Error Rate (BER)
|
<10 -12
|
|
Environmental Specifications
|
|
Operating Temperature
|
0 C to 50 C (32 F to 122 F)
|
|
Storage Temperature
|
minimum range of -25 C to 70 C (-13 F to 158 F)
|
|
Operating Humidity
|
5% to 90% non-condensing
|
|
Storage Humidity
|
5% to 95% non-condensing
|
|
Operating Altitude
|
Up to 3,048 meters (10,000 feet)
|
Heat Output
( BTU/HR )
|
6.8
|
|
MTBF (Hours)**
|
Without power adaptor: 595,000
With power adaptor: 333,000
|
|
Mounting
|
|
Din Rail Kit
|
Optional
|
|
Rack Mount Kit
|
Optional
|
|
Product Weight and Dimensions
|
|
Weight
|
0.3 kg, 0.66 lbs
|
|
Dimentions
|
120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches
|
|
Packaging
|
|
Shipping Weight
|
0.55 kg, 1.2 lbs
|
|
Shipping Dimentions
|
170 x 280 x 70 mm, 6.7 x 10.2 x 2.8 inches
|
|
Regulatory Approvals
|
|
Emissions
|
FCC Part 15 Class B*, EN55022 Class B*
|
|
CISPR 22 Class B*
|
|
EN61000-3-2
|
|
Immunity
|
EN55024
|
|
Electrical Safety
|
UL 60950-1
|
|
EN60950
|
|
CE
|
|
Laser Safety
|
EN 60825-1:2007
|
|
Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.
|
|
Environmental
|
Reach, RoHS and WEEE Compliant
|
|
Other
|
ECCN: 5A991A
|
|
HTSUS Number: 8517.62.0050
|
|
Perle Limited Lifetime Warranty
|
