| Media Converter Module Indicators |
| Power / TST |
This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode. |
| Fiber link on / Receive activity (LKF) |
This green LED is operational only when power is applied.
The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received. |
| Copper link on / Receive activity (LKC) |
This green LED is operational only when power is applied.
The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received. |
| Management Module Indicators / reset |
| Power |
Blinking green during startup cycle Steady green: module has power and is ready
Red : error |
| ALM |
Red alarm indicator activated when an alert event occurs |
| LKC |
Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data |
| 100/1000 |
Green - 1000 Mbps link
Yellow - 100 Mbps link
Off - 10 Mbps or no Link |
| Reset button |
Recessed pinhole button resets module |
| Connectors |
| 100Base-TX |
RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable
Magnetic Isolation - 1.5kv |
| Fiber Optic Cable |
Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron
Single Mode: 9/125 micron (ITU-T 625) |
| Management ethernet port |
10/100/1000Base-T - RJ45
Auto- MDI/MDIX |
| Management console port |
RS232 Serial RJ45 - Cisco pinout for use with standard CAT5 "rolled cable" (crossover) 9600 to 115k bps 7/8 bits Odd,even, no parity 1/2 stop bits Hardware/software flow control DCD/DSR monitoring |
| Packet Transmission Characteristics |
| Bit Error Rate (BER) |
<10 -12 |
| Switches: On-Board (If Auto/Switch strap is set to Switch) |
| Auto-Negotiation (802.3u) |
Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex.
Disabled - The media converter sets the 100Base-TX port to full duplex. |
| Pause |
Pause should be enabled when all devices connected to the media converter support pause. Auto-Negotiation must be Enabled to use this feature.
Enabled (Default) - The Media converter will advertise Pause capability during Auto-Negotiation on the 100Base-TX interface.
Disabled - The Media converter will advertise that it does not have Pause capability during Auto-Negotiation on the 100Base-TX interface. |
| Link Pass Through |
Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on.
Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface. |
| Far-End Fault (FEF) |
Enabled (Default) - The media converter transmits the Far-End Fault Indication over the 100Base-FX fiber connection whenever a receive failure is detected on the 100Base-FX fiber connection. The media converter continuously monitors the100Base-X fiber connection and clears the Far-End Fault Indication condition when a valid signal is received.
Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection. |
| Remote Loopback |
The media converter can perform a loopback on the 100Base-X fiber interface.
Disabled (Default - Up)
Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface. |
| Auto-MDIX (Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media convertor's transmitter and the partner devices transmitter are connected to the others receiver. The Media Convertor's 100Base-TX port is configured as MDI with this switch setting. |
| Configuration Mode (Strap) |
Auto (default) enable management module to overwrite hardware switch settings
Switch - Use onboard DIP switches |
| Power |
| Input Supply Voltage |
( 12 vDC Nominal ) |
| Current |
0.33amps at12vdc |
| Power Consumption |
3.98watts |
| Power Connector |
4.1 mm Barrel Connector |
| Power Adapter |
| Universal AC/DC Adapter |
100-240v AC, regulated DC adapter included |
| Environmental Specifications |
| Operating Temperature |
0 C to 50 C (32 F to 122 F) |
| Storage Temperature |
minimum range of -25 C to 70 C (-13 F to 158 F) |
| Operating Humidity |
5% to 90% non-condensing |
| Storage Humidity |
5% to 95% non-condensing |
| Operating Altitude |
Up to 3,048 meters (10,000 feet) |
| Heat Output ( BTU/HR ) |
13.6 |
| MTBF (Hours) |
245,769 without power adaptor
168,532 with power adaptor: |
| Mounting |
| Din Rail Kit |
Optional |
| Rack Mount Kit |
Optional |
| Product Weight and Dimensions |
| Weight |
0.722 kg |
| Dimentions |
175 x 145 x 23 mm |
| Packaging |
| Shipping Weight |
1.2 kg |
| Shipping Dimentions |
300 x 200 x 70 mm |
| Regulatory Approvals |
| Emissions |
FCC Part 15 Class A, EN55022 Class A |
| CISPR 22 Class A |
| EN61000-3-2 |
| Immunity |
EN55024 |
| Electrical Safety |
UL 60950-1 |
| EN60950 |
| CE |
| Laser Safety |
EN 60825-1:2007 |
| Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. |
| Environmental |
RoHS - 2002/95/EC Directive |
| WEEE - 2002/96/EC Directive |
| Reach compliant |
| Other |
ECCN: 5A991A |
| HTSUS Number: 8517.62.0050 |
| Perle Lifetime warranty |
