Perle 06005284 - IndustrialDirect.com

Home > Perle > Perle Ethernet Extenders > Perle Stand-Alone Ethernet Extenders > Perle PoE Ethernet Extenders > 10/100/1000 PoE/PoE+ Ethernet Extenders >

06005284

See any errors on this page?
Please let us know.

Perle eXP-4S1110PE-BNC - Gigabit Ethernet Stand-Alone PoE+ Ethernet Extender - 4 port 10/100/1000Base-T (RJ-45) [100 m/328 ft.]. BNC Interlink ( VDSL2 ) connector. Provides power over Ethernet as a PSE. 57V 75W PoE+ power adapter included

List Price: $1,271.00

Our Price: $991.20

Contact Us for Partner Pricing. (more info)

Availability:: Usually Ships in 24 Hours; However, Due To Shortages Contact Sales to Verify
Product Code: 06005284

Description

Technical Specs

Drivers & Downloads

Perle eXP-S1110PE PoE+ Gigabit Ethernet Extenders transparently extend Ethernet beyond the general IEEE 802.3at limits of 328ft / 100m while providing Power over Ethernet ( PoE+ ) to standards-based compliant devices such as IP cameras, VoIP phones and wireless access points.

This technology enables users to transparently extend up to four 10/100/1000 Power over Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ), coax or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.

These PoE+ Ethernet Extenders are classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle eXP-S1110PE PoE Ethernet Extenders provide up to 30 watts of power to Powered Devices (PDs). Learn more about PoE.

These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments, and connecting a remote office or private-network backbone to a corporate LAN … anywhere you need 10/100/1000 Ethernet communication links for PoE+ devices up to 10,000ft (3KM) in distance.

Perle’s advanced features such as Link Pass-Through* and Interlink Fault Feedback*, Loopback and remote PD reset*, enable Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eXP-S1110PE PoE+ Gigabit Ethernet Extenders are also available with support for PoE.

eXP-S1110PE PoE+ Gigabit Ethernet Extender Features

Extend Ethernet over twisted pair	Extend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km )
Extend Ethernet over Coaxial cable	Extend an Ethernet link over 75 ohm coaxial cable
On-board PoE Power Controller	As a fully compliant IEEE 802.3af and 802.3at PSE end-span device, this Ethernet Extender’s PoE power controller provides compliant power provisioning and monitoring, properly sensing through signature detection whether or not the attach Ethernet devices are PoE capable or not. This provides a safe connection for both PoE and Non-PoE capable devices. Competitive PoE Ethernet Extender products operate as a simple passive power injector and will always apply power to RJ45 port pins which may result in damage if non-PoE compliant Ethernet devices are accidently attached. Click here for more details
Advanced Power capabilities	ALT A/B and legacy PoE/PoE+ RJ45 pin selection Current limiting protection Remote PD reset
Fully compliant 802.3af PoE and 802.3at POE+ PSE	Enable/Disable PSE power PD signature detection Over-Current Protection PD power classification detection ( Class 0,1,2,3,4 )
PSE Status Indicator	A multi-color LED provided presents the status of the PSE function for easy troubleshooting of power over Ethernet connections
PD Power Reset ( Port 1 )	Ideal for remotely resetting equipment, this configurable function performs a momentary power reset to the attached Powered Device (PD) on Port #1. Read our PD Reset Tech Note for further details on this feature
Broadest range of PoE devices supported	Support is included for a broad range of PD ( Powered Devices ) IEEE 802.3af, 802.3at PoE/PoE+ ( Alternative A and B ) Legacy High Capacitance PDs Cisco legacy VoIP phones and Wireless Access Points
Hi-Speed Performance	Utilizes second generation VDSL2 technology ( ITU-T Recommendation G.993. ). When operating under “Profile 30a”, Perle Ethernet Extenders can provide an aggregate VDSL line rate capability of up to 200 mbps. Actual distance and performance may vary depending on the type / gauge and condition of the wire used and if required, the amount of power you require across the VDSL Link
Plug and Play operation	Perle Ethernet Extenders will automatically configure your VDSL interlink connection. The CO/CPE peer association will be determined automatically by the Ethernet Extender. No need to set CO / CPE VDSL pairing. Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link.
Link Pass-Through*	With Link Pass-Through the state of the 10/100/1000Base-T Ethernet connection is “passed through” the VDSL link to the 10/100/1000Base-T Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early. Competitive Ethernet extenders without this feature will never detect or report any error conditions.
Interlink Fault Feedback*	Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers.
Auto-Negotiation	The Ethernet Extender supports auto negotiation on the 10/100/1000Base-T interface.
Auto-MDIX	Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100/1000 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
Fixed Speed and Duplex	Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches.
VLAN	Transparent to tagged VLAN ( 802.1Q ) packets.
Transparent to IP Video compression protocols	Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG.
Power Strain Relief strap	A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration.
Loopback	When enabled, will perform a loopback on the copper VDSL Interlink.

*Available on 1 port models.

Documentation

PDF eXP-S1110PE PoE+ Gigabit Ethernet Extenders Installation Guide

Power

eXP-1S1110PE

eXP-4S1110PE

Unit Powered by

Local power adapter

Provides Power to:

Ethernet

Power adapter connector

Barrel or terminal block

Input Voltage Range from adapter

46V to 57

Input Voltage Range from VDSL (parasitic)

24 to 57

Universal AC Adapter

56vDC, 75 watt adapter included

Power Connectors

5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block

Ethernet

eXP-1S1110PE

eXP-4S1110PE

10/100/1000Base-T Port(s)

1 port RJ45 Shielded

4 port RJ45 Shielded

Auto-MDIX

Auto-MDIX enables proper operation with either straight-through or crossover cabling

Distance

Distance up to 100 meters ( 328 feet ) as per IEEE 802.3

Maximum Frame Size

1522

Type of PoE device

Type 2 PSE ( PoE+ ) IEEE 802.3at

PoE PSE Maximum Power (Watts)

Refer to the Power Reach Installation Planning Guide

PoE PSE RJ45 Cable Pinout

Alternative A ( default ) on all ports

Alternative B: selectable on port #1

Legacy Cisco Pre-Standard: selectable on port #1

Pins 3,6 Neg, Pins 1,2 Pos

Pins 7,8 Neg, Pins 4,5 Pos

Pins 7,8 Pos, Pins 4,5 Neg

VDSL – Interlink

eXP-1S1110PE

eXP-4S1110PE

Connector

Choice of RJ45, BNC or terminal block models for VDSL link connector

RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
BNC – Coaxial 75 ohm cable with BNC connector
Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling

Copper Cabling

Ethernet Extenders must be connected in pairs using unconditioned wire between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ). Circuits that run through signal equalization equipment are not permitted.

VDSL Line Rate/Reach

Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG ( 0.5 MM ) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models.

High Speed Asymmetric
Reach ( Distance )		VDSL Rate ( Mbps )
feet	meters	Downstream	Upstream
250	76	195	105
500	152	182	98
1000	305	141	63
1500	457	93	45
2000	610	66	30
2500	762	53	12
3000	914	44	8
3500	1000	36	5

High Speed Symmetric
Reach ( Distance )		VDSL Rate ( Mbps )
feet	meters	Downstream	Upstream
250	76	190	110
500	152	180	105
1000	305	122	83
1500	457	84	50
2000	610	64	26
2500	762	53	10
3000	914	42	7
3500	1000	36	4

Long Reach Symmetric
Reach ( Distance )		VDSL Rate ( Mbps )
feet	meters	Downstream	Upstream
250	76	76	57
1000	305	74	49
2500	762	52	10
4000	1219	28	2
5500	1676	15	1.5
7000	2134	8	1.4
8500	2591	5	1.3
10000	3000	2	0.9

Long Reach Asymmetric
Reach ( Distance )		VDSL Rate ( Mbps )
feet	meters	Downstream	Upstream
250	76	78	16
1000	305	76	16
2500	762	52	10
4000	1219	28	2
5500	1676	15	1.5
7000	2134	8	1.4
8500	2591	5	1.3
10000	3000	2	0.9

Power Budget

The amount of available power at the PoE+ PD is dependent on the scenario planned.

Refer to the Power Reach Installation Planning Guide

Indicators

eXP-1S1110PE

eXP-4S1110PE

Power / TST

This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.

CO - Local

Ethernet Extender is operating in CO VDSL mode

CPE - remote

Ethernet Extender is operating in CPE VDSL mode

ILNK

Indicates Link Status and activity on the Interlink (VDSL) port

ETH

Indicates link status and activity on Ethernet port(s).

PSE Status

This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE;

GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied)

YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :

Not connected
Has not detected a compliant PD and is not applying power
PSE has turned off power for Reset function

OFF — PSE function switch disabled

RED — Blinking: Error Conditions

Capacitance too High — 1 blink
Resistance too Low or short circuit — 2 blinks
Resistance too high or open circuit — 3 blinks

Switches

eXP-1S1110PE

eXP-4S1110PE

Access

Switch settings are accessible through a side opening in the chassis

Rate/Reach

Two switches enable the user to select the right balance between speed and distance for their environment.

Signal to Noise Ratio

Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.

Auto-Negotiation (802.3u) control on Port 1

Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex.

Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

Force Ethernet Speed on Port 1

When Auto-Negotiation switch is disabled, a fixed speed can be forced on port 1

100 (Default)
10

Force Ethernet Duplex on Port 1

When Auto-Negotiation switch is disabled, Full or half Duplex can be forced on port 1

Full (Default)
Half

Link Mode*

Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.

Link Pass-Through- the state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer.

Interlink Fault Feedback*

Enabled – A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers

Disabled ( Default ) - The state of the VDSL link is not propagated to the 10/100/1000Base-T port

Loopback

Enabled – The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its remote peer.

Disabled (Default - Up)

PD Reset ( Port 1 )

When enabled ( down ), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again.

When PD Power Reset is disabled ( default ), loss of VDSL link has no effect on power supplied to the PD device.

Environmental Specifications

eXP-1S1110PE

eXP-4S1110PE

Operating Temperature

0 C to 50 C (32 F to 122 F)

Storage Temperature

minimum range of -25 C to 70 C (-13 F to 158 F)

Operating Humidity

5% to 90% non-condensing

Storage Humidity

5% to 95% non-condensing

Operating Altitude

Up to 3,048 meters (10,000 feet)

Current mA

114 @ 56vdc

163 @ 56vdc

Unit Power Consumption watts

6.4

9.1

Heat Output
( BTU/HR )

21.84

31.05

MTBF with power adapter (Hours)**

75,029

72,416

MTBF without power adapter (Hours)**

300,472

262,530

Mounting

eXP-1S1110PE

eXP-4S1110PE

Wall/Desk

Standard

Din Rail Kit

Optional

Rack Mount Kit

Optional

Product Weight and Dimensions

eXP-1S1110PE

eXP-4S1110PE

Weight

0.58 Kg, 1.3 lbs

0.61Kg, 1.34 lbs

Dimensions

163 x 116 x 37 mm, 6.4 x 4.6 x 1.46 inches

Packaging

eXP-1S1110PE

eXP-4S1110PE

Shipping Weight

1.27 Kg, 2.8 lbs

1.3 Kg, 2.86 lbs

Shipping Dimensions

20 x 30 x 7 cm, 7.9 x 11.8 x 2.8 inches

Regulatory Approvals

eXP-1S1110PE

eXP-4S1110PE

Emissions

EN 55022

CISPR 22

IEC/EN 61000-3-2

IEC/EN 61000-3-3

Immunity

EN 55024:2010

CISPR 24:2010

IEC/EN 61000-4-2

IEC/EN 61000-4-3

IEC/EN 61000-4-4

IEC/EN 61000-4-5

IEC/EN 61000-4-6

IEC/EN 61000-4-8

IEC/EN 61000-4-11

Electrical Safety

EN60950-1

IEC 60950-1

UL 60950-1

CSA C22.2 No. 60950-1

Environmental

Reach, RoHS and WEEE Compliant

Other

ECCN: 5A991A

HTSUS Number: 8517.62.0050

Perle Lifetime warranty

*Available on 1 port models.

**MTBF Calculation model based on MIL-HDBK-217-FN2 @ 30 °C

Features

Extends 10/100/1000Base-T Ethernet up to 10,000 feet ( 3 KM ) over 2-wire 24 AWG twisted pair or Coaxial cable
Power remote PoE+ devices across 2-wire twisted pair or coaxial cable
On-board PoE+ power controller for true compatibility with IEEE 802.3at standard
Hi-Speed – up to 200 mbps aggregate line rate
Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes.
Advanced features: Link Pass-Through*, Interlink Fault Feedback*, Auto-MDIX
and Loopback, remote PD power reset*, Plug and Play - Auto configuration of VDSL