 |
 |
 |
|
Introduction
MGate 5111 industrial Ethernet gateways convert data between the Modbus RTU/ASCII/TCP, EtherNet/IP, PROFINET, and PROFIBUS protocols. All models are protected by a rugged metal housing, are DIN-rail mountable, and offer built-in serial isolation.
Modbus is one of the most widely used industrial communication protocols, and EtherNet/IP, PROFINET, and PROFIBUS are commonly used in factory automation and process automation. The MGate 5111 supports both Modbus RTU/ASCII/TCP master and slave modes, so that you can easily connect your Modbus device to PROFIBUS PLCs or DCSs, such as Siemens PLCs.
For system integration, the MGate 5111 can connect to EtherNet/IP PLC/SCADA systems, such as Rockwell Automation PLCs, to PROFIBUS PLC/DCS systems, or between a new Siemens PLC system that supports PROFINET to an existing PROFIBUS system. The MGate 5111 gateways are designed for easy configuration and quick maintenance. A handy web console can be used to implement remote maintenance tasks, and the configuration wizard UI lets you quickly set up your gateway. A comprehensive collection of troubleshooting tools reduce configuration time and system downtime. The rugged design is suitable for industrial applications, such as factory automation, power, oil and gas, water and wastewater, and other process automation industries.
Easy Configuration
The MGate 5111 Series has a user-friendly interface that lets you quickly set up protocol conversion routines for most applications, doing away with what were often time-consuming tasks in which users had to implement detailed parameter configurations one by one. With Quick Setup, you can easily access protocol conversion modes and finish the configuration in a few steps.
The MGate 5111 supports a web console and Telnet console for remote maintenance. Encryption communication functions, including HTTPS and SSH, are supported to provide better network security. In addition, system monitoring functions are provided to record network connections and system log events.
A Variety of Maintenance Functions
The MGate 5111 supports Protocol Diagnose and Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues caused by incorrect software parameters, such as slave IDs and register addresses, or incorrect command configurations, can be fished out with Protocol Diagnose and Traffic Monitoring, which let you capture and check data to easily identify root causes.
MGate 5111 gateways also support status monitoring and fault protection functions. The status monitoring function notifies a PLC/DCS/SCADA system when a Modbus device gets disconnected or does not respond, in which case the process PLC/DCS gets the status of each end device and then issues alarms to notify operators. When a PROFIBUS cable gets disconnected, the fault protection function executes actions on end devices identified by a predefined value set by the user.
Documentation
 Data Sheet
PDF Quick Start Guide
PDF User Manual
-
microSD Slot
Up to 32 GB (SD 2.0 compatible)
-
Contact Current Rating
Resistive load: 2 A @ 30 VDC
-
10/100BaseT(X) Ports (RJ45 connector)
2
Auto MDI/MDI-X connection
-
Magnetic Isolation Protection
-
Industrial Protocols
EtherNet/IP Adapter (Slave), Modbus TCP Client (Master), Modbus TCP Server (Slave), PROFINET IO Device (Slave)
-
Configuration Options
Device Search Utility (DSU), Web Console, Telnet Console
-
Management
ARP, DHCP Client, DNS, HTTP, HTTPS, SMTP, SNMP Trap, SNMPv1/v2c/v3, TCP/IP, Telnet, SSH, UDP
-
MIB
-
Time Management
-
Console Port
RS-232 (TxD, RxD, GND), 8-pin RJ45 (115200, n, 8, 1)
-
Baudrate
-
Connector
-
Data Bits
-
Flow Control
RTS Toggle (RS-232 only), RTS/CTS
-
Isolation
-
No. of Ports
-
Parity
None, Even, Odd, Space, Mark
-
RS-485 Data Direction Control
ADDCŪ (automatic data direction control)
-
Pull High/Low Resistor for RS-485
1 kilo-ohm, 150 kilo-ohms
-
Serial Standards
-
Stop Bits
-
Terminator for RS-485
-
RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
-
RS-422
-
RS-485-2w
-
RS-485-4w
-
Configuration Options
-
Industrial Protocols
Modbus RTU/ASCII Master, Modbus RTU/ASCII Slave
-
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
-
Mode
-
Input Data Size
-
Max. No. of Commands
-
Output Data Size
-
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
-
Input Data Size
-
Max. No. of Client Connections
-
Max. No. of Commands
-
Max. No. of Server Connections
-
Output Data Size
-
Mode
-
Baudrate
-
Connector
-
Industrial Protocols
-
Isolation
-
No. of Ports
-
Signals
PROFIBUS D+, PROFIBUS D-, RTS, Signal Common, 5V
-
Mode
-
Rotary Switch
PROFIBUS addresses 0-99 (addresses 100-125 supported through software configuration)
-
Input Data Size
-
Max. No. of Master Connections
-
Max. No. of PROFIBUS I/O Modules
-
Output Data Size
-
Input Data Size
-
Max. No. of IO Controller Connections
-
Mode
-
Output Data Size
-
CIP Objects Supported
Identity, Message Router, Assembly, Connection Manager, TCP/IP interface, Ethernet link, Port
-
Input Data Size
-
Max. No. of Scanner Connections
1 (for read-only), 1 (for read/write)
-
Mode
-
Output Data Size
-
Input Current
-
Input Voltage
-
Power Connector
Spring-type Euroblock terminal
-
Housing
-
IP Rating
-
Dimensions
45.8 x 105 x 134 mm (1.8 x 4.13 x 5.28 in)
-
Weight
-
Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
-
Storage Temperature (package included)
-40 to 85°C (-40 to 185°F)
-
Ambient Relative Humidity
5 to 95% (non-condensing)
-
Safety
EN 60950-1, UL 61010-2-201
-
EMC
-
EMI
CISPR 32, FCC Part 15B Class A
-
EMS
IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 4 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 10 V/m; Signal: 10 V/m
IEC 61000-4-8 PFMF
-
Hazardous Locations
ATEX, Class I Division 2, IECEx
-
Freefall
-
Shock
-
Vibration
IEC 60068-2-6
IEC 60068-2-64
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Protocol conversion between Modbus, PROFINET, EtherNet/IP, and PROFIBUS
- Supports PROFIBUS DP V0 slave
- Supports Modbus RTU/ASCII/TCP master/client and slave/server
- Supports EtherNet/IP Adapter
- Supports PROFINET IO device
- Effortless configuration via web-based wizard
- Built-in Ethernet cascading for easy wiring
- Embedded traffic monitoring/diagnostic information for easy troubleshooting
- Status monitoring and fault protection for easy maintenance
- microSD card for configuration backup/duplication and event logs
- Supports redundant dual DC power inputs and 1 relay output
- Serial port with 2 kV isolation protection
- -40 to 75°C wide operating temperature models available
- Security features based on IEC 62443
|
|
|
|
|
|
|