 |
 |
 |
|
Introduction
NPort 5600-8-DT device servers can conveniently and transparently connect 8 serial devices to an Ethernet network, allowing you to network your existing serial devices with only basic configuration. You can both centralize management of your serial devices and distribute management hosts over the network. Since the NPort 5600-8-DT device servers have a smaller form factor compared to our 19-inch models, they are a great choice for applications that need additional serial ports, but for which mounting rails are not available.
Convenient Design for RS-485 Applications
The NPort 5650-8-DT device servers support selectable 1 kilo-ohm and 150 kilo-ohms pull high/low resistors and a 120-ohm terminator. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals. When using termination resistors, it is also important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible with all environments, NPort 5600-8-DT device servers use DIP switches to allow users to adjust termination and pull high/low resistor values manually for each serial port.
Convenient Power Inputs
The NPort 5650-8-DT device servers support both power terminal blocks and power jacks for ease of use and greater flexibility. Users can connect the terminal block directly to a DC power source, or use the power jack to connect to an AC circuit through an adapter.
LED Indicators to Ease Your Maintenance Tasks
The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The NPort 5600’s LEDs not only indicate current system and network status, but also help field engineers monitor the status of attached serial devices.
Two Ethernet Ports for Convenient Cascade Wiring
The NPort 5600-8-DT device servers come with two Ethernet ports that can be used as Ethernet switch ports. Connect one port to the network or server, and the other port to another Ethernet device. The dual Ethernet ports eliminate the need to connect each device to a separate Ethernet switch, reducing wiring costs.
-
10/100BaseT(X) Ports (RJ45 connector)
-
Magnetic Isolation Protection
-
Configuration Options
Serial Console, Telnet Console, Web Console (HTTP/HTTPS), Windows Utility
-
Management
ARP, BOOTP, DHCP Client, DNS, HTTP, HTTPS, ICMP, IPv4, LLDP, Rtelnet, SMTP, SNMPv1/v2c, TCP/IP, Telnet, UDP
-
Filter
-
MIB
-
Time Management
-
Windows Real COM Drivers
Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2/2016/2019 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded
-
Linux Real TTY Drivers
Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x
-
Fixed TTY Drivers
SCO UNIX, SCO OpenServer, SCO UnixWare 7, Sun Solaris 10, QNX 4.25, QNX 6.x, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X
-
Android API
-
Connector
8-pin RJ45:
NPort 5610-8-DT-J/5650-8-DT-J
DB9 male:
NPort 5610-8-DT models/NPort 5650-8-DT models/NPort 5650I-8-DT models
-
No. of Ports
-
Serial Standards
NPort 5610-8-DT Series: RS-232
NPort 5650-8-DT Series: RS-232/422/485
-
Baudrate
Supports standard baudrates (unit=bps): 50, 75, 110, 134, 150, 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 19200, 38400, 57600, 115200, 230.4k, 460.8k, 921.6k
-
Data Bits
-
Stop Bits
-
Parity
None, Even, Odd, Space, Mark
-
Flow Control
RTS/CTS, DTR/DSR, XON/XOFF
-
Pull High/Low Resistor for RS-485
1 kilo-ohm, 150 kilo-ohms
-
Terminator for RS-485
-
RS-485 Data Direction Control
ADDC® (automatic data direction control)
-
Isolation
-
Surge
-
Console Port
RS-232 (TxD, RxD, GND), 3-pin (19200, n, 8, 1)
-
RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
-
RS-422
-
RS-485-4w
-
RS-485-2w
-
Input Current
NPort 5610-8-DT/NPort 5610-8-DT-J/NPort 5610-8-DT-T: 611 mA @ 12 VDC
NPort 5650-8-DT/NPort 5650-8-DT-J/NPort 5650-8-DT-T: 615 mA @ 12 VDC
NPort 5650I-8-DT/NPort 5650I-8-DT-T: 1066 mA @ 12 VDC
-
No. of Power Inputs
-
Input Voltage
-
Reverse Polarity Protection
-
Automatic Reboot Trigger
-
Alert Tools
Built-in buzzer and RTC (real-time clock)
-
Housing
-
Dimensions (with ears)
229 x 46 x 125 mm (9.01 x 1.81 x 4.92 in)
-
Dimensions (without ears)
197 x 44 x 125 mm (7.76 x 1.73 x 4.92 in)
-
Dimensions (with DIN-rail kit on bottom panel)
197 x 53 x 125 mm (7.76 x 2.09 x 4.92 in)
-
Weight
NPort 5610-8-DT: 1,570 g (3.46 lb)
NPort 5610-8-DT-J: 1,520 g (3.35 lb)
NPort 5610-8-DT-T: 1,320 g (2.91 lb)
NPort 5650-8-DT: 1,590 g (3.51 lb)
NPort 5650-8-DT-J: 1,540 g (3.40 lb)
NPort 5650-8-DT-T: 1,340 g (2.95 lb)
NPort 5650I-8-DT: 1,660 g (3.66 lb)
NPort 5650I-8-DT-T: 1,410 g (3.11 lb)
-
Installation
Desktop, DIN-rail mounting (with optional kit), Wall mounting (with optional kit)
-
Interactive Interface
LCD panel display
Push buttons for configuration
-
Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
-
Storage Temperature (package included)
-40 to 75°C (-40 to 167°F)
-
Ambient Relative Humidity
5 to 95% (non-condensing)
-
EMC
-
EMI
CISPR 32, FCC Part 15B Class A
-
EMS
IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 0.5 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11
-
Safety
-
Time
-
Standards
Telcordia (Bellcore) Standard
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- 8 serial ports supporting RS-232/422/485
- Compact desktop design
- 10/100M auto-sensing Ethernet
- Easy IP address configuration with LCD panel
- Configure by Telnet, web browser, or Windows utility
- Socket modes: TCP server, TCP client, UDP, Real COM
- SNMP MIB-II for network management
|
|
|
|
|
|
|